Copyright © 2011-2019 MultiMedia Soft How to use the Windows Audio Compression Manager

The Windows Audio Compression Manager (MSACM32.DLL) allows an application to convert data between different formats. By itself, the ACM is not capable of performing any conversions. Instead, it relies on installable drivers to perform specific conversions. These drivers are called codecs, converters, or filters (sometimes the term codec is used in a more generic sense, to refer to all three types of ACM drivers).

 

A codec converts from one format to another; for example, from PCM to MS-ADPCM. A converter converts between different types of the same format; for example, between 8 and 16 bit PCM, between mono and stereo, and between different PCM sampling frequencies.  A filter modifies the audio data without changing the format; for example, an echo filter might make a 44,100 Hz PCM wave file sound different, but it would still be a 44,100 Hz PCM file.

 

There are several ACM drivers that are automatically installed with the Windows system (other ACM drivers can be installed at any time). There are drivers that provide support for the compressed formats MS-ADPCM, IMA ADPCM, the GSM 6.10 standard, the TrueSpeech voice and the MPEG Layer-3 coding format.

 

The first thing to do in order to take advantage of Audio Compression Manager features, is to set the EncodeFormats.FormatToUse property to ENCODING_FORMAT_ACM; after this first setting you can proceed with ACM codecs, using properties and methods exposed by the EncodeFormats.ACM property, in one between the following 2 ways:

 

 

This approach can be predisposed setting the EncodeFormats.ACM.EncodeMode property to ACM_ENCODE_USE_CODEC_INDEX

 

Then you need to enumerate codecs installed inside the target PC through a call to its EncodeFormats.ACM.InitCodecs method.

 

At this point you can obtain the total number of supported codecs through a call to the EncodeFormats.ACM.GetCodecsCount method: for each codec you can obtain the friendly name through the EncodeFormats.ACM.GetCodecDesc method. These two methods will allow filling a combobox as seen on the screenshot below:

 

 

Finally you can enumerate the formats supported by the codec chosen above; the total number of supported formats can be obtained through a call to the EncodeFormats.ACM.GetCodecFormatsCount method: for each of the available formats you can obtain the friendly description through the EncodeFormats.ACM.GetCodecFormatDesc method. Also in this case, these two methods will allow filling a combobox as seen on the screenshot below:

 

 

 

 

 

As you may know, each codec's format is described through a WAVEFORMATEX data structure: the WAVEFORMATEX structure, common to all waveform-audio formats, is defined inside the Microsoft SDK as follows:

 

typedef struct {

 WORD  wFormatTag;

 WORD  nChannels;

 DWORD nSamplesPerSec;

 DWORD nAvgBytesPerSec;

 WORD  nBlockAlign;

 WORD  wBitsPerSample;

 WORD  cbSize;

} WAVEFORMATEX;

The cbSize parameter defines how many extra-bytes, specific for a certain codec, are appended to the end of the WAVEFORMATEX structure

 

In certain situations, for example if your application doesn't allow a user interaction for selecting from a combobox the codec and the respective format, you may require the possibility to fill a WAVEFORMATEX structure and to pass it directly to the EncodeACM class: in this case you can start setting the EncodeFormats.ACM.EncodeMode property to ACM_ENCODE_USE_WAV_FORMAT.

 

Once predisposed, the WAVEFORMATEX structure can be set into the control through a call to the EncodeFormats.ACM.SetCodecFormatWavData method.

 

It's important to note that further encoding through the format defined inside the WAVEFORMATEX structure will not work if the specific codec is not installed on the target PC.

 

Just for your information, if you have already enumerated the available codecs and respective formats, as seen inside the previous point, the total size in bytes of the WAVEFORMATEX data structure that describes a given format, including any extra-byte the specific format may require, can be obtained using the EncodeFormats.ACM.GetCodecFormatWavDataLength method. The returned size of the WAVEFORMATEX data structure, expressed in bytes, can be used to allocate a buffer that will be filled by a call to the EncodeFormats.ACM.GetCodecFormatWavData method.

 

 

Once chosen one between the ways above, you can start the needed exporting session using the ExportToFile method.